Just How to Remove as Well as Replace a Tub
Just How to Remove as Well as Replace a Tub
Blog Article
What are your concepts about How to Install a Bathtub Yourself?
Setting up a bathtub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the job can move quickly; if you need to open a wall to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually certified yourself for the job and also fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not require to change the plan of your previous water supply pipelines.
Your tools and also material list should consist of the following:
Planning for the Setup
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other tap.
Turn on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will certainly settle it into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Protect the tap in position with the maker given backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is advisable to fit the tiles making use of waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking time to read our article post. Liked our blog posting? Please share it. Help other people find it. Thanks for going through it.
This Resource
Report this page